Facebook Icon YouTube Icon LinkedIn Icon Twitter Icon RSS Icon

Your First Stop for Piledriving Technology News

Archive for "Jun 2009"

APE and Linde-Griffith Construction Go to the Mall

When Chris Shannon with Linde-Griffith Construction of Newark, NJ needed to vibrate 30′ XZ85 sheets in tough cohesive clays, he put the call in to APE Northeast. The APE 200 Vibro at 4400 in/lbs was dispatched to the site to get the job done. Pictured is the APE 200 in action at the Echelon Mall in Voorhees, NJ. Linde-Griffith Construction, in business for over 100 years, was hired to drive sheet pile to hold back the existing parking lot for Macy’s department store. Eventually a combination of retail and residential space will be constructed.

The experienced staff at Linde-Griffith know who to call for the industry’s most technologically advanced, reliable pile driving equipment- they GO APE! We greatly appreciate their repeat business. Please call Paul Kuzik at 201-400-8356 for all of your deep foundation equipment needs.

Share and Enjoy:
  • Facebook
  • Twitter
  • Google Buzz
  • Yahoo! Buzz
  • MySpace
  • Digg
  • StumbleUpon
  • del.icio.us
  • Add to favorites
  • Print
  • email
  • RSS

Bridge Building in Three Letters = MCM

What can be said of MCM Construction of Northern California? Where can we start when taking a look at one of California’s major bridge builders? Lets see…

1) MCM Construction has built some of the most amazing bridges in California from North to South from start to finish. Massive multi level interchanges that make one dizzy just to look at and beautiful scenic bridges that span 100 foot deep gorges that are wonderful to look at and admire.
2) MCM Construction has Randy Notnagel as Piledriving General Superintendant who just happens to be one of the industry’s leading men in piledriving and foundation work.
3) Jim Carter, owner of MCM Construction, isn’t afraid to tackle any project, even the S.F. BAY BRIDGE APPROACH, which just happens to have 8’ diameter pipe pile driven to depths of 160 feet!
4) MCM Construction of Northern California uses APE equipment to get their pile in the ground!

These are just a few things that make MCM Construction great! Not to mention that they drive GREAT BIG PILES! As seen here, MCM Construction uses the APE model D180-42 single acting diesel hammer with a ram weight of close to 40,000lbs and an energy rating over 450,000ftlbs to drive their MASSIVE eight foot diameter CISS pile. These monster piles are 160 feet long and are being driven into existing bed rock formations for the Oakland California Highway 880 project located in the heart of the city where there are tremendous amounts of traffic every day!
These piles are huge! When the APE D180-42 finished driving the 8 foot diameter pile, the 4 foot diameter reaction piles are driven with his baby brother the APE D100-42. “These piles get bigger and bigger, so the equipment gets bigger and bigger to get the piles driven!” says Randy Notnagel. “The D180 makes the D100 look like a tinker toy.”
We soon forget the days when a big hammer was a D62-22 driving 36” pipe pile. That was huge in the day, but what do you expect when you want to drive across some of the safest bridges in America? Tinker Toys? Those days are gone and that is why MCM Construction uses APE equipment to get their pile in the ground, because if you want to go deep, “Go APE”!

Share and Enjoy:
  • Facebook
  • Twitter
  • Google Buzz
  • Yahoo! Buzz
  • MySpace
  • Digg
  • StumbleUpon
  • del.icio.us
  • Add to favorites
  • Print
  • email
  • RSS

LANE CONSTRUCTION GOES APE ON TITUSVILLE BRIDGE

Lane Construction has been chosen as the design/build contractor for a new bridge over the Indian River in Titusville, Florida. The new bridge is named The Maxwell Brewer Bridge, construction began on June 1.
This 3100-ft long, 4-lane bridge will replace a 2-lane drawbridge which is over 50 years old. The new bridge will eliminate traffic congestion; while speeding hurricane evacuation of the nearby Kennedy Space Center and the surrounding areas including the nudist colony at nearby Canaveral Beach.
The foundations for the bridge and approaches include 64 – 36” square piles over 200 feet long each. There are also 84 – 30” square piles of the same length and 118 – 24” piles. The 36” and the 30” piles are all spliced piles. A spliced pile is usually more difficult to drive correctly because the permitted stress specifications are reduced by approximately 50%. To prevent overstressing the pile, the energy going into the pile from the hammer must be strictly controlled. Lane has chosen an APE D-125 diesel hammer for the 36” piles and an APE D-100 diesel hammer for the 30”. An APE D-62 will drive the 24” piles.
The diesel hammers feature the hydraulic start mechanism and the APE hydraulic fuel system. This system permits finite stroke height control which translates into excellent pile stress reduction.
In addition to the diesel hammers, the project will employ APE vibros for the sheet piling and pile template construction. An APE Model 75 hydraulic earth auger will be used to pre-drill for the 24” piles under the approach slabs.
Lane’s bridge superintendent, Paul Roux states: “ We look to APE to assist us with our pile driving. APE equipment arrives at the jobsite properly prepared, performs flawlessly and, if a problem comes up, APE service technicians always provide prompt and effective product support at the jobsite. Project downtime is minimized.”
Pile installation will continue for the balance of 2009 and should be completed by the end of the year. APE will be there to offer support if needed.

Share and Enjoy:
  • Facebook
  • Twitter
  • Google Buzz
  • Yahoo! Buzz
  • MySpace
  • Digg
  • StumbleUpon
  • del.icio.us
  • Add to favorites
  • Print
  • email
  • RSS

Taylor /Brothers Marine Sheds light on Harkers Island North Carolina

Harkers Island North Carolina is attached to the main land by a small 1/2 mile long bridge. The only electric power that is brought to the island is by means of an older out dated power pole system 200 feet away from the bridge. The currrent poles are aprox. 30 feet long. Some time ago some of the main poles were damaged by a water spout. The power company knew it was time for a much needed update on this system. They decided to install 54″ dia. concrete cylinder piles 56 feet in length for the new poles foundations and use poles 85 feeet in length that are un-guyed. They called “Taylor Brothers Marine” of Beauford North Carolina. TBM knew this was not an off the shelf type job. TBM contacted APE Mid-Atlantic of Virginia Beach, Virginia. APE ‘s engineers reviewed the soils data & job specfications and put togeather an APE D62-42 diesel impact hammer with hydraulic trip / start in a special offshore leader just for driving 54″ cylinder piles. This could’nt have gone any smoother than it did, talk about the right tool for the right job said Julias Taylor & Julias Taylor the 3rd.Why would a contractor use anyone but APE! APE wishes TBM a safe & productive project. Do you have a difficult upcomming job? or any upcomming job, if so contact your nearest APE branch to see what they can do for you……………. GO APE!

Share and Enjoy:
  • Facebook
  • Twitter
  • Google Buzz
  • Yahoo! Buzz
  • MySpace
  • Digg
  • StumbleUpon
  • del.icio.us
  • Add to favorites
  • Print
  • email
  • RSS

APE’s New Pile Driving Rig

Many years ago APE introduced the Junttan Pile Driving Rig into the USA. It was a very difficult venture because the rig was very expensive. In addition, Junttan’s delivery schedule was more than one year. APE sold one rig to Picone and one to Jet Drive, both New York contractors. There were many issues with parts and service and getting things through customs.

APE’s agreement with Junttan excluded APE from selling to Skanska Companies. The agreement became too restricted plus Junttan wanted to sell direct so we parted ways a few years ago. APE still maintains a fleet of Junttan hydraulic hammers. For the record I want to say that Junttan builds a very nice rig. We are proud to say that we played a very large part of introducing their technology to the USA. We learned from Junttan and they learned from APE.

APES NEW RIG

APE set out to design its own rig with the best features from both the Junttan and ABI rigs. We wanted capacity but we also wanted our leader system to pivot on the rig. We joined forces with Nippon and in 2008 we introduced the first APE rig. Here it is driving 4000 pipe piles in Florida.

The APE rig can drive longer piles than ABI’s rig. The APE rig mast can pivot sideways unlike the fixed mast Junttan rig. APE can fit the rig with a low headroom APE hydraulic hammer or a vibro as shown or a diesel hammer. APE considers this rig to be superior to the Junttan or ABI rigs. APE is in the process of putting one rig in each APE branch. So far we have rigs in Florida and New Jersey. Texas will get the third rig.

For more information please contact Jim Casavant at the APE Florida branch or on his cell at 863-660-8716.

Share and Enjoy:
  • Facebook
  • Twitter
  • Google Buzz
  • Yahoo! Buzz
  • MySpace
  • Digg
  • StumbleUpon
  • del.icio.us
  • Add to favorites
  • Print
  • email
  • RSS

News Navigation

Search

APE Branches

Latest Posts

  • May 14 2014
    APE Model 600 Vibro Leading the Way
  • Feb 13 2014
    APE Canada on the Red River
  • Feb 13 2014
    Neither Snow, nor More Snow, nor even More Snow…
  • Dec 19 2013
    Chris Corp
  • Apr 17 2013
    APE / J&M 110K Drill Test Pile

  • Enter your email address to subscribe to this blog and receive notifications of new posts by email.

    Join 10 other subscribers

  • APE News Article Calendar

    June 2009
    M T W T F S S
    « May   Jul »
    1234567
    891011121314
    15161718192021
    22232425262728
    2930  
  • APE News Article Archives

Update News

APE Partners Alessi Equipment Deef Foundations Institute Pile Driving Contractors Association IMECO Collins Company Internation Association of Foundation Drilling Terresolve Foundation Associates SEMW