Modular Vibrating of Monopiles for Offshore Wind Farm Riffgat:
Halfway June APE Holland started on the North Sea near the German island of Borkum with a special offshore project, vibrating 30 steel piles (monopiles) on which 30 windmills will be installed. The piles will be driven with the Super Quad Kong (SQK), an innovative and modular vibratory driver/extractor consisting of four APE vibros, which are connected to four hypermodern power packs, providing a total eccentric moment of 920 kg-m. By using the SQK vibratory hammer it is able to drive these monopiles environmentally friendly in a single run in the correct position at the bottom of the sea.
Strict Environmental Regulation/Rules:
APE Holland is pleased that the contractor Seaway Heavy Lifting chose the option of using a vibratory hammer. “By choosing this innovative way of vibrating, APE Holland can comply to the strict environmental rules which apply in Germany,” explains Martijn Kleine, Sales Manager at APE Holland. “The damage to the environment by noise and vibrations remains within acceptable limits.” By using the traditional piling techniques with the conventional hydraulic hammers the noise is at a level that it causes major damage to marine life. “There are various solutions to reduce the noise, but it does imply that the piles have to be vibrated first,” said Martijn Kleine. From the wish to have such piles driven without the use of impact hammers, APE Holland developed modular vibration techniques. “The noise of our hammer is much lower than a traditional hammer and the vibration process is faster than piling”.
The Super Quad Kong is specially developed for this offshore wind farm Riffgat in the North Sea, where Seaway Heavy Lifting is using their newest state of the art crane vessel “Oleg Strashnov”. “After driving the first monopiles it was clear that our modular built vibratory hammer supplies sufficient power to show impressive results. For the first piles, we only used 50% of the total power of these hammers. With our SQK vibro we are able to drive these monopoles to a penetration of 31 meters in one run. The reason that the last 10m of the piles on the Riffgat field still had to be driven with an impact hammer has a reason. The owner of the field required a so called “blowcount”, which indicates the bearing capacity of the pile. This can only be done with an impact hammer until now.” After the vibratory hammer was taken off the pile, a Noise Migration System (NMS) was put around the pile, after which the IHC S-1800 hydrohammer was put on the pile. Kleine: “Where the pile was moving in only a few seconds after the SQK was switched on, driving the first 10 meters with the hydrohammer started labored. For the first 25cm 100 blows of 1200 kJ were required to get the pile moving again. After that, the blowcount went back to 25 blows on the 25 cm.”
The monopiles which are used for the Riffgat wind farm project weighing between the 480 en 720 ton each. The length of the piles are between 53 and 70 meters with a diameter of 4,7 m on the top of the pile and a diameter of 5,7 up to 6,5 m at the pile tip. APE Holland got this contract awarded thanks to a nice reference project in China. For the construction of two artificial islands in the fixed link between Hong Kong and Macau, the APE OctaKong was used. This enormous vibrator was built up out of 8 linked vibrators which vibrated 130 steel monopiles with a length of 40 m. about 25m into the seabed. The piles with a diameter of 22 m had a weight between 500 and 650 tons each. The insertion of each pile take less than 10 minutes.
APE Holland cooperated on this project with Allnamics (www.allnamics.eu), who carried out the drive-ability studies for the monopiles. The long and extensive experience in Geotechnical Engineering of Allnamics was of extreme value for the OctaKong project and showed the value on the Riffgat project again.
APE Holland BV is the exclusive supplier in Europa and Russia of APE vibratory hammers and power packs. The sister company CAPE Holland BV designs and manufactures the modular systems with multiple vibratory hammers and power packs for APE Holland BV. Both companies are part of the Cape Holland Group and have great knowledge and skill in developing innovative techniques in vibration. “We are unique in coupling different techniques, material and equipment that can be used together as one,” says Martijn Kleine. “Our experience with the OctaKong gave us an advantage in developing the Super Quad Kong for this project. Besides the vibratory hammer we are also supplying the required operational assistance for the operating our equipment for this wind farm project in the North Sea. And the next project for the piling of monopiles has already been signed.”
The article and pictures of the project from the CAPE Holland website can be found here (pictures) and here (article). For further information about modular vibratory systems the OctaKong and Super Quad Kong contact:
APE Holland BV
Romhof 5, 9411 SB Beilen The Netherlands
Telephone: +31(0) 593 54 08 91. Telefax: +31(0) 593 54 27 84